Main Article Content
Abstract
The research aimed at investigating of the influence of surface roughing at semi-precast slab to slab strength on the first crack and the ultimate, the slab strength ratio made monolithically and composite, and to investigate crack and failure pattern of composite slab. The testing was conducted on two groups of slab which has 1:1 scales. Each group consists of three. The first group was monolith slab as control speciment. The second group was composite slab with
surface roughing. The test was conducted on two step. The first step, speciment was loaded by the repeated center static loading (10 cycle), the second step, the speciment was loaded from zero and increased step by step until speciment failed. Testing results showed that the first crack load of composite slab was approximately 14,2 % (width of 200 mm), 10,61 % (width of 400 mm), and 22,64 % (width of 600 mm) less than monolith slab. The ultimate (failure) load of composite slab was about 32,2 % (width of 200 mm), 9,8 % (width of 400 mm), and 15,9 % (width of 600 mm) less than monolith slab. The cracks occurred at slab speciment was vertical cracks extending through tensile side. The crack was indicated flexural crack, while the kind of failure type occurred at slab speciment was flexural failure.
Article Details
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
- This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
References
- Badan Standarisasi Nasional. 2007. Tata Cara Perhitungan Struktur Beton
- Untuk Bangunan Gedung (SNI 03- 2847-2002). ITS Press, Surabaya.
- Dipohusodo, I. 1999. Sruktur Beton Bertulang. Gramedia Pustaka Utama,
- Jakarta.
- Fragiacomo, M. 2008. Timber Floor Solutions, Timber Design Seminar,
- New Zealand.
- MacCormac, J.C. 2001. Desain Beton Bertulang. Edisi Kelima, Jilid 1,
- Erlangga, Jakarta.
- Timoshenko, P. dan Gere. 1987. Mekanika Bahan. Erlangga, Jakarta.
- Triwiyono, A. 1999. Bahan Ajar Mekanika Bahan. Jurusan Teknik Sipil Fakultas Teknik UGM.
- Wang, C.K. and Salmon, C.G. 1994. Desain Beton Bertulang. Edisi Keempat, Jilid 1, Erlangga, Jakarta.
References
Badan Standarisasi Nasional. 2007. Tata Cara Perhitungan Struktur Beton
Untuk Bangunan Gedung (SNI 03- 2847-2002). ITS Press, Surabaya.
Dipohusodo, I. 1999. Sruktur Beton Bertulang. Gramedia Pustaka Utama,
Jakarta.
Fragiacomo, M. 2008. Timber Floor Solutions, Timber Design Seminar,
New Zealand.
MacCormac, J.C. 2001. Desain Beton Bertulang. Edisi Kelima, Jilid 1,
Erlangga, Jakarta.
Timoshenko, P. dan Gere. 1987. Mekanika Bahan. Erlangga, Jakarta.
Triwiyono, A. 1999. Bahan Ajar Mekanika Bahan. Jurusan Teknik Sipil Fakultas Teknik UGM.
Wang, C.K. and Salmon, C.G. 1994. Desain Beton Bertulang. Edisi Keempat, Jilid 1, Erlangga, Jakarta.