Bilah Samping Artikel

Telah diserahkan
December 16, 2019
Diterima
December 16, 2019
Diterbitkan
December 20, 2019
Unduh
PDF (English)
Statistik
Baca Penghitung : 104 Unduh : 768

Isi Artikel Utama

Abstrak

A nozzle of diameter 25 cm of a closed coupled type was set at an outlet gap 0,05 mm to atomize polyethylene terephthalate plastic wastes. Parameters of pressure and heating temperature were varied into 5 bar, 6 bar and 7 bar pressures, and at 275?C, 285?C and 295?C heating. A vessel to collect the product was 40 cm diametrally away from the nozzle mouth. The products were the form of powders, yarn and liquid. The powders were only 4,77%, 6,45% and 2,94% of each heating temperature aforementioned.

Rincian Artikel

Lisensi
Lisensi Creative Commons
Ciptaan disebarluaskan di bawah Lisensi Creative Commons Atribusi-BerbagiSerupa 4.0 Internasional.
Biografi Penulis

Hari Pamuji, Mechanical Engineering University of Bengkulu

Mechanical Engineering

A Sofwan F Alqap, Mechanical Engineering University of Bengkulu

Metallurgy, Material Sciences, Bio Materials

Agus Suandi, Mechanical Engineering University of Bengkulu

Mechanical Engineering

Cara Mengutip
Pamuji, H., Alqap, A. S. F., & Suandi, A. (2019). CHARACTERIZATION OF WASTE PET POWDER AS ATOMIZATION PRODUCT. Rekayasa Mekanika: Jurnal Ilmiah Teknik Mesin, 3(2), 15–19. https://doi.org/10.33369/rekayasamekanika.v3i2.9861
Unduh Sitasi
Endnote/Zotero/Mendeley (RIS)
BibTeX

Referensi

  1. Upadhyaya G,S, 2002, Powder Metallurgy Technology. Department of Materials and Metallurgical Engineering Indian Institute of Technology, Kanpur, India
  2. Nur Budi, dan Totok, 2006, Pengaruh sudut water sprayer dan tekanan air dalam sprayer pump terhadap hasil serbuk alumunium pada proses atomisasi air. Teknik Mesin Fakultas Teknik Universitas Muhammadiyah Yogyakarta
  3. M. Halim Asiri, 2014, Karakterisasi Serbuk Hasil Produksi Menggunakan Metode Atomisasi, Jurusan Teknik Mesin Fakultas Teknik Universitas Brawijaya Malang
  4. Pramono, Agus dan Salahuddin Junus, 2011, Karakteristik fisik dan struktur mikro komposit logam aluminium-grafit hasil proses metalurgi serbuk,
  5. Liu, Huimin, 1981, S cience and engineering of droplets, William Andrew Publishing Norwich,
  6. New York, U.S.A.
  7. Anantha H. Krishnan, 2011, Study of total oxygen content and oxide composition formed during water atomization of steel powders due to manganese variation, Department of Material Science and Engineering Royal Institute of Technology (KTH) SE-100 44 Stockholm
  8. Mujiarto, Iman, 2005, Sifat Dan Karakteristik Material Plastik Dan Bahan Aditif, Traksi. Vol.3. No. 2.
  9. Ahmad.2002. Mikroskop Optik. http://kambing.ui.ac.id/bebas/v12/sponsor/Sponsorpendamping/Praweda/Fisika/0335%20Fis-3-3b.htm. Diakses pada tanggal 02 april 2017 pukul 15. 10 WIB
  10. Rosidatul Mahmudah S. dan Lukman Atmaja, Ph.D, Pengaruh Konsentrasi Katalis Kalium Karbonat pada Proses Depolimerisasi Limbah Botol Plastik Polietilen Tereftalat (PET) Jurusan Kimia, Fakultas Matematika dan Ilmu Pengetahuan Alam, Institut Teknologi Sepuluh Nopember (ITS).